273.15K下LiCl-Li2B4O7-H2O体系热力学性质的等压研究   总被引：2，自引：0，他引：2       下载免费PDF全文

杨吉民  姚燕  张爱云  宋彭生 《盐湖研究》2005,13(1):19-24

用等压法研究了273 15K下LiCl-Li2B4O7-H2O体系中纯盐水溶液(离子强度范围为LiCl0 2046～2 5055mol·kg-1,Li2B4O70 1295～0 3700mol·kg-1)以及混合盐水溶液(离子强度范围为0 0931～2 4911mol·kg-1)渗透系数和水活度;计算了LiCl-Li2B4O7-H2O体系的饱和蒸汽压,获得饱和蒸汽压、渗透系数随离子强度的变化规律。用实验数据以最小二乘法求取了LiCl和Li2B4O7纯盐参数及体系的混合盐参数,拟合的标准偏差分别为0 0077和0 026。用该模型计算的渗透系数值与实验结果取得合理的一致。同时研究结果与273 15K下LiCl-Li2SO4-H2O体系的渗透系数随离子强度变化的规律作了比较。本研究对完善低温下含锂、硼盐湖卤水体系的热力学模型和盐湖资源的综合开发利用具有重要意义。  相似文献   

用叠加谱比法研究新疆地区Lg尾波Q值的区域性变化     

徐彦  毛燕  胡家富  苏有锦  丛连理 《云南地理环境研究》2005,17(2):6-10,27

运用叠加谱比法,对分布于新疆地区的5个台站所记录的51个地震数据进行分析,得出与各射线路径相对应的Lg尾波Q0(Lg尾波在1Hz处的Q)值。结果表明:Q0值呈现出明显的区域性变化特点,与构造活动关系紧密。在较为稳定的塔里木地台,Q0呈现出高值,在350～450之间。在南部构造活动较为激烈的昆仑褶皱系,Q0呈现出较低的值,约为200～250。在构造活动最为激烈的帕米尔地区,Q0值在170～200之间。在北部的天山褶皱系,Q0值约为220～270。准葛尔褶皱系比天山褶皱系的Q0值略高,约为260～290。  相似文献   

An alternative Boussinesq equation considering the effect of hysteresis on coastal groundwater waves          下载免费PDF全文

Jun Kong  Zhaoyang Luo  Chengji Shen  Guofen Hua  Hongjun Zhao 《水文研究》2016,30(15):2657-2670

This paper presents an alternative Boussinesq equation considering hysteresis effect via a third‐order derivative term. By introducing an improved moisture–pressure retention function, this equation describes, with reasonable precision, groundwater propagation in coastal aquifers subject to Dirichlet boundary condition of different oscillation frequencies. Test results confirmed that it is necessary to consider horizontal and vertical flows in unsaturated zone, because of their variable influences on hysteresis. Hysteresis in unsaturated zone can affect the water table wave number of groundwater wave motion, such as wave damping rate and phase lag. Oscillations with different periods exert different hysteresis effect on wave propagation. Truncation/shrinkage of unsaturated zones also affects the strength of hysteresis. These impacts can be reflected in the alternative Boussinesq equation by adjusting the parameter representing the variation rate of moisture associated with pressure change, as opposed to traditional computationally expensive hysteresis algorithms. The present Boussinesq equation is simple to use and can provide feasible basis for future coupling of groundwater and surface water models. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

Mixing of event and pre‐event water in a shallow Entisol in sloping farmland based on isotopic and hydrometric measurements,SW China          下载免费PDF全文

Pei Zhao  Xiangyu Tang  Peng Zhao  Wei Zhang  Jialiang Tang 《水文研究》2016,30(19):3478-3493

Water percolation and flow processes in subsurface geologic media play an important role in determining the water source for plants and the transport of contaminants or nutrients, which is essential for water resource management and the development of measures for pollution mitigation. During June 2013, the dynamics of the rainwater, soil water, subsurface flows and groundwater in a shallow Entisol on sloping farmland were monitored using a hydrometric and isotopic approach. The results showed that effective mixing of rainwater and soil water occurred in hours. The rebound phenomenon of δD profiles in soils showed that most isotope‐depleted rainwater largely bypassed the soil matrix when the water saturation in the soil was high. Preferential‐flow, which was the dominant water movement pattern in the vadose zone, occurred through the whole soil profile, and infrequent piston‐flow was mainly found at 20–40 cm in depth. The interflow in the soil layer, composed of 75.2% rainwater, was only generated when the soil profile had been saturated. Underflow in the fractured mudrock was the dominant flow type in this hillslope, and outflow was dominated by base flow (groundwater flow) with a mean contribution of 76.7%. The generation mechanism of underflow was groundwater ridging, which was superimposed upon preferential‐flow composed mainly of rainwater. The quick mixing process of rainwater and soil water and the rapid movement of the mixture through preferential channels in the study soil, which shows a typical bimodal pore size distribution, can explain the prompt release of pre‐event water in subsurface flow. Water sources of subsurface flows at peak discharge could be affected by the antecedent soil water content, rain characteristics and antecedent groundwater levels. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

Refined modeling and movement characteristics analyses of irregularly shaped particles          下载免费PDF全文

Y. W. Zeng  L. Jin  X. Du  R. Gao 《国际地质力学数值与分析法杂志》2015,39(4):388-408

Irregularly shaped (IRS) particles widely exist in many engineering and industrial fields. The macro physical and mechanical properties of the particle system are governed by the interaction between the particles in the system. The interaction between IRS particles is more complicated because of their complex geometric shape with extremely irregular and co‐existed concave and convex surfaces. These particles may interlock each other, making the sliding and friction of IRS particles more complex than that of particles with regular shape. In order to study the interaction of IRS particles more efficiently, a refined method of constructing discrete element model based on computed tomography scanning of IRS particles is proposed. Three parameters were introduced to control the accuracy and the number of packing spheres. Subsequently, the inertia tensor of the IRS particle model was optimized. Finally, laboratory and numerical open bottom cylinder tests were carried out to verify the refined modeling method. The influence of particle shape, particle position, and mesoscopic friction coefficient on the interaction of particles was also simulated. It is noteworthy that with the increase of mesoscopic friction coefficient, the fluidity of IRS particle assembly decreases, and intermittent limit equilibrium state may appear. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

Fracture mechanics analysis of multiple cracks in anisotropic media     

Chia‐Huei Tu  C.‐S. Chen  T.‐T. Yu 《国际地质力学数值与分析法杂志》2011,35(11):1226-1242

This paper presents a single‐domain boundary element method (BEM) for linear elastic fracture mechanics analysis in the two‐dimensional anisotropic material. In this formulation, the displacement integral equation is collocated on the un‐cracked boundary only, and the traction integral equation is collocated on one side of the crack surface only. A special crack‐tip element was introduced to capture exactly the crack‐tip behavior. A computer program with the FORTRAN language has been developed to effectively calculate the stress intensity factors of an anisotropic material. This BEM program has been verified having a good accuracy with the previous researches. Furthermore, by analyzing the different anisotropic degree cracks in a finite plate, we found that the stress intensity factors of crack tips had apparent influence by the geometry forms of cracks and media with different anisotropic degrees. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

Discrete element method modeling of inherently anisotropic rocks under uniaxial compression loading          下载免费PDF全文

K. Duan  C.Y. Kwok  M. Pierce 《国际地质力学数值与分析法杂志》2016,40(8):1150-1183

A new numerical approach is proposed in this study to model the mechanical behaviors of inherently anisotropic rocks in which the rock matrix is represented as bonded particle model, and the intrinsic anisotropy is imposed by replacing any parallel bonds dipping within a certain angle range with smooth‐joint contacts. A series of numerical models with β = 0°, 15°, 30°, 45°, 60°, 75°, and 90° are constructed and tested (β is defined as the angle between the normal of weak layers and the maximum principal stress direction). The effect of smooth‐joint parameters on the uniaxial compression strength and Young's modulus is investigated systematically. The simulation results reveal that the normal strength of smooth‐joint mainly affects the behaviors at high anisotropy angles (β > 45°), while the shear strength plays an important role at medium anisotropy angles (30°–75°). The normal stiffness controls the mechanical behaviors at low anisotropy angles. The angle range of parallel bonds being replaced plays an important role on defining the degree of anisotropy. Step‐by‐step procedures for the calibration of micro parameters are recommended. The numerical model is calibrated to reproduce the behaviors of different anisotropic rocks. Detailed analyses are conducted to investigate the brittle failure process by looking at stress‐strain behaviors, increment of micro cracks, initiation and propagation of fractures. Most of these responses agree well with previous experimental findings and can provide new insights into the micro mechanisms related to the anisotropic deformation and failure behaviors. The numerical approach is then applied to simulate the stress‐induced borehole breakouts in anisotropic rock formations at reduced scale. The effect of rock anisotropy and stress anisotropy can be captured. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

Spatiotemporal estimation of snow depth using point data from snow stakes,digital terrain models,and satellite data          下载免费PDF全文

Antonio‐Juan Collados‐Lara  Eulogio Pardo‐Igúzquiza  David Pulido‐Velazquez 《水文研究》2017,31(10):1966-1982

Snow availability in Alpine catchments plays an important role in water resources management. In this paper, we propose a method for an optimal estimation of snow depth (areal extension and thickness) in Alpine systems from point data and satellite observations by using significant explanatory variables deduced from a digital terrain model. It is intended to be a parsimonious approach that may complement physical‐based methodologies. Different techniques (multiple regression, multicriteria analysis, and kriging) are integrated to address the following issues: We identify the explanatory variables that could be helpful on the basis of a critical review of the scientific literature. We study the relationship between ground observations and explanatory variables using a systematic procedure for a complete multiple regression analysis. Multiple regression models are calibrated combining all suggested model structures and explanatory variables. We also propose an evaluation of the models (using indices to analyze the goodness of fit) and select the best approaches (models and variables) on the basis of multicriteria analysis. Estimation of the snow depth is performed with the selected regression models. The residual estimation is improved by applying kriging in cases with spatial correlation. The final estimate is obtained by combining regression and kriging results, and constraining the snow domain in accordance with satellite data. The method is illustrated using the case study of the Sierra Nevada mountain range (Southern Spain). A cross‐validation experiment has confirmed the efficiency of the proposed procedure. Finally, although it is not the scope of this work, the snow depth is used to asses a first estimation of snow water equivalent resources.  相似文献   

Using raw regional climate model outputs for quantifying climate change impacts on hydrology          下载免费PDF全文

Jie Chen  François P. Brissette  Pan Liu  Jun Xia 《水文研究》2017,31(24):4398-4413

General circulation model outputs are rarely used directly for quantifying climate change impacts on hydrology, due to their coarse resolution and inherent bias. Bias correction methods are usually applied to correct the statistical deviations of climate model outputs from the observed data. However, the use of bias correction methods for impact studies is often disputable, due to the lack of physical basis and the bias nonstationarity of climate model outputs. With the improvement in model resolution and reliability, it is now possible to investigate the direct use of regional climate model (RCM) outputs for impact studies. This study proposes an approach to use RCM simulations directly for quantifying the hydrological impacts of climate change over North America. With this method, a hydrological model (HSAMI) is specifically calibrated using the RCM simulations at the recent past period. The change in hydrological regimes for a future period (2041–2065) over the reference (1971–1995), simulated using bias‐corrected and nonbias‐corrected simulations, is compared using mean flow, spring high flow, and summer–autumn low flow as indicators. Three RCMs driven by three different general circulation models are used to investigate the uncertainty of hydrological simulations associated with the choice of a bias‐corrected or nonbias‐corrected RCM simulation. The results indicate that the uncertainty envelope is generally watershed and indicator dependent. It is difficult to draw a firm conclusion about whether one method is better than the other. In other words, the bias correction method could bring further uncertainty to future hydrological simulations, in addition to uncertainty related to the choice of a bias correction method. This implies that the nonbias‐corrected results should be provided to end users along with the bias‐corrected ones, along with a detailed explanation of the bias correction procedure. This information would be especially helpful to assist end users in making the most informed decisions.  相似文献   

An Eocene/Oligocene blueschist‐/greenschist facies P–T loop from the Cycladic Blueschist Unit on Naxos Island,Greece: Deformation‐related re‐equilibration vs. thermal relaxation          下载免费PDF全文

Alexandre Peillod  Uwe Ring  Johannes Glodny  Alasdair Skelton 《Journal of Metamorphic Geology》2017,35(7):805-830

Geothermobarometric and geochronological work indicates a complete Eocene/early Oligocene blueschist/greenschist facies metamorphic cycle of the Cycladic Blueschist Unit on Naxos Island in the Aegean Sea region. Using the average pressure–temperature (P–T) method of thermocalc coupled with detailed textural work, we separate an early blueschist facies event at 576 ± 16 to 619 ± 32°C and 15.5 ± 0.5 to 16.3 ± 0.9 kbar from a subsequent greenschist facies overprint at 384 ± 30°C and 3.8 ± 1.1 kbar. Multi‐mineral Rb–Sr isochron dating yields crystallization ages for near peak‐pressure blueschist facies assemblages between 40.5 ± 1.0 and 38.3 ± 0.5 Ma. The greenschist facies overprint commonly did not result in complete resetting of age signatures. Maximum ages for the end of greenschist facies reworking, obtained from disequilibrium patterns, cluster near c. 32 Ma, with one sample showing rejuvenation at c. 27 Ma. We conclude that the high‐P rocks from south Naxos were exhumed to upper mid‐crustal levels in the late Eocene and early Oligocene at rates of 7.4 ± 4.6 km/Ma, completing a full blueschist‐/greenschist facies metamorphic cycle soon after subduction within c. 8 Ma. The greenschist facies overprint of the blueschist facies rocks from south Naxos resulted from rapid exhumation and associated deformation/fluid‐controlled metamorphic re‐equilibration, and is unrelated to the strong high‐T metamorphism associated with the Miocene formation of the Naxos migmatite dome. It follows that the Miocene thermal overprint had no impact on rock textures or Sr isotopic signatures, and that the rocks of south Naxos underwent three metamorphic events, one more than hitherto envisaged.  相似文献